Airbox Convertible Upgrade HP
With the AirBox Convertible Upgrade HP you will be able to work with the following printhead cartridges:
| Zone 1 | Zone 2 | Zone 3 | Zone 4 |
| USA | Europe | Asia | China&India |
| 17 | 17 | 17 | 17 |
| 23 | 23 | 23 | 23 |
| 41 | 41 | 41 | 41 |
| 78A | 78A | 78A | 78A |
| 78D | 78D | 78D | 78D |
| 21 | 21 | 21 | 21 |
| 21XL | 21XL | 21XL | 21XL |
| 22 | 22 | 22 | 22 |
| 22XL | 22XL | 22XL | 22XL |
| 27 | 27 | 27 | 27 |
| 28 | 28 | 28 | 28 |
| 54 | 54 | 54 | 54 |
| 56 | 56 | 56 | 56 |
| 57 | 57 | 57 | 57 |
| 58 | 58 | 58 | 58 |
| 59 | 59 | 59 | 59 |
| 60 | 300 | 121 | 818 |
| 60XL | 300XL | 121XL | 818XL |
| 61 | 301 | 122 | 802 |
| 74 | 350 | 140 | 860 |
| 74XL | 350XL | 140XL | 860XL |
| 75 | 351 | 141 | 861 |
| 75XL | 351XL | 141XL | 861XL |
| 92 | 336 | 132 | 850 |
| 93 | 342 | 136 | 854 |
| 94 | 338 | 131 | 852 |
| 95 | 343 | 135 | 855 |
| 96 | 339 | 130 | 853 |
| 97 | 344 | 134 | 857 |
| 98 | 337 | 129 | 851 |
| 99 | 348 | 138 | 858 |
| 100 | 100 | 100 | 100 |
| 102 | 102 | 102 | 102 |
| 110 | 110 | 110 | 110 |
| 901 | 901 | 901 | 901 |
For working with this AirBox Convertible Upgrade HP you need also the AirBox Convertible Basis Part!
How to use the AirBox Convertible
What you need in addition:
- a pump
- refilled printhead cartridges
- a lintless cloth
- The upgrade for HP has to be assembled into the AirBox Basis Part.
- On the back side of the upgrade you can see 4 holes (2 at the upper edge and 2 at the lower edge) for fixing the upgrade on the 4 center screws of the AirBox Basis Part.
- Hold the upgrade that way in which you are able to read the markings and press it down carefully between the valve banks of the Basis Part.
- Take care that the Upgrade is centered on the 4 screws of the Basis Part.
- Now mount the included tubes in the correct order:
- thick PU tube
- tube connector
- thin PU tube
- tube connector
- silicone tube with yellow tube reduction
- Luer-Lock tube connector
- Connect the PU tube with your pump.
- Combine the white Luer-Lock connector with the valve bank you decided to work with.
- Make yourself familiar with the arrangement of valve banks and the numbers leading to the seperate channels of the upgrade.
- Valve No. I opens channel no. I, valve no. II opens channel no. II and so on.
- Switch on the pump.
- Every valve has 3 levers. If the valve is open the mid-lever points to the connected tube. If the valve is closed the mid-lever points at the opposite direction or upwards.
- Insert the selected cartridge into the upgrade's notch - printhead facing up. The cartridge's ventilation holes fit exactly on the air channels of the upgrade.
- Please start with the darkest ink. Process the lightest color at last!
- Open slowly the desired channel and keep the lintless cloth at hand.
- Press the cartridge into the upgrade's rubber slightly with one finger.
- Tap slightly onto the number near the opened valve to control the air flow to the ink chamber.
- When ink is coming out of the printhead wipe it off carefully with the lintless cloth.
- Please wipe only from back to front - just like the direction the nozzles are arranged in the printhead.
- Process this until you can see a constant ink flow without breaks.
- If the result is satisfying interrupt the air flow to the ink chamber by closing the valve.
- After that you can process the other ink chambers of the cartridge.
- Make a testprint.
- If the printout is perfect you have removed all bubbles.
- If the printout is streaky, start at the beginning. You only have to process the colors which cause the white lines in your testprint.
